PROFESSIONAL ABRIDGEMENT:

7 years of work experience in Design, Development, Verification & Validation, Testing, Qualification of Product, Project Lead, Project Management, Procurement of raw material and Scrum Master. Skilled in Analog, Digital and High - speed circuits in Electrical Electronics products make me confident seeking a challenging position in a company.

TECHNICAL SKILLS:

Schematic Tools: Altium Designer, ORCAD Capture & Allegro, PADS, Mentor Graphics Dx Designer & Hyperlynx.

Hardware Design: Analog, Digital, High Speed, AC-DC, DC-DC, Low Power, LDO, Linear Regulator.

Interfaces: Differential lines, PCI, SPI, I2C, I2S, RS232, RS422, Ethernet, Parallel bus, USB, UART, GPS.

Equipment: Oscilloscope, E-Load, logic Analyzer, Power Analyzer, Signal Analyzer, Generators, Multimeter.

Industries: Automotive, Aerospace, Consumer Electronics, Industrial Automation, Manufacturing.

Programming Acquaintance: Ability to read & perceive Existing code in C/C++, VHDL, Verilog.

Standards Exposure: Familiar with BSEE, IEEE, UL Stds and respective Internal company quality STDs.

Documentation: PRD, PDR, FRS, HLDD, DDD, FMEAs, TS, TR, QTP, EMI-EMC, ENV, UM, SIP, Datasheet.

EMI/EMC: ESD, Conducted Immunity, Radiated Immunity, Radiated Emissions, CE, Surge, EFT, etc.

Environment: al Tests Shock & Vibration, Drop test, Stress Test, Temperature, Thermal Cycling.

PROFESSIONAL EXPERIENCE:

Confidential

Responsibilities:

• Good at checking the Feasibility of different ways of doing form ideas generation to Release.
• Familiar with engineering design process and product life cycle.
• Developed in different types of Analog Sensors signal conditioner modules like Strain, Pressure, Ultrasonic, vibration, acceleration, Potentiometer, Flow rate, Temperature using FPGA & SOC based boards etc.
• Designed various digital boards with Microprocessors, Microcontrollers of different Vendors like Microchip, Renesas, Texas Instruments, ST Microelectronics, and Silicon Labs.
• Development of Power Management solutions such as DC to DC Converters, Low Drop out Regulators, Linear Regulators, Battery Management, Motor driving control system.
• Components Selection, Block diagram, Schematics Preparation, Bill of Material Finalization.
• Experience in doing Electrical Wiring diagrams such as Electrical Integration Architecture.
• Experience in Multiple interfaces like DDR, SDRAM, SRAM, Flash, RS 232/422/485.
• Development of motor drives, inverters, SMPS, AC to DC Converters and DC to DC Converters, LDO’s, Linear Regulators.
• Experience in test setups, test equipment maintenance, support, inventory, procurement.
• Familiar with engineering design process and defining Product hardware Architecture.
• Understanding of Basic Firmware and ability to understand existing code and modify it.
• Knowledge in Arduino ATMega2560 Evolution board. It is 8-bit Microcontroller with 256K in System Programmable Flash, 54 Digital input/Outputs out of 14 can be used as PWM outputs for Motor control, 16 MHz of Clock speed, input voltage is (7-12V) DC, and 16 Analog inputs.
• Knowledge on Inertial Navigation systems (INS), GPS & Inertial Measurement Unit (IMU).
• Knowledge on Programmable logic controllers (PLC’s), Analog, Digital Inputs & Output (IO) Modules, Relay Output Modules, LAN Modules, Ethernet devices etc.

Confidential

Responsibilities:

• Hands on Experience in Power budget Calculations, Thermal & Heat dissipation Analysis.
• Expertise in doing simulations for Analog & Power Electronics circuits.
• Experience with PCB layout oversight using Allegro.
• Knowledge in High-speed design, Noise suppression techniques.
• Expertise in execution of Electrical Design Verification Test cases.
• Good electrical measurement techniques.
• Excellent debug skills of board and test set-up issues.
• Ability to provide innovative test solutions and fixtures.
• Expertise in soldering skills for board/test set-up modifications.
• Take the product through development, compliance testing, operator testing, ramp up and sustaining.
• Experience with Technical document writing using Visio, Word, Excel, and / or PowerPoint.
• Experience with Revision and Document control.
• Experience in doing in circuit Test, Board brings up, Functional Test, and Board level Tests.
• Ability to provide innovative test solutions and fixtures.
• Works with other functional teams to Investigate root cause issues and find solutions.
• Experience in EMI/EMC Tests, Vibration, Acceleration, Shock, Thermal Cycling, High Temperature, Low Temperature, Pressure, Rain, Tropical, High Altitude, Sand & Dust, Bump.
• Validated hardware and software in hostile environments by performing environmental tests.

Confidential

Responsibilities:

• Share the ideas with different suppliers on various design approaches.
• Exchange the information with seniors and management to approvals for various stages.
• Works with Software team to develop the Graphical user interface platform.
• Communicate with Firmware team to write the Programming for the main controller in the board.
• Co-ordinate with Procurement team on purchasing the components.
• Synchronize with PCB Engineer on Placement, Layout, Layer Stack up and Routing.
• Correlate with Mechanical Engineer on Product Dimensions and Arrangement of Connectors.
• Collaborates with Management, Product Marketing, Planning, Quality, regarding project progress.

Production/Manufacturing support

Confidential

Responsibilities:

• Develop and maintain instrument/subsystem test station for production.
• Expertise in soldering skills for board/test set-up modifications.
• Guide Technicians on through hole Component Soldering, Potting and Conformal coating for PCB Assembly and wiring and Involved on Manufacturing Process and Familiar with ROHS & Non ROHS Process.
• Knowledge on Stencil usage, Apply Solder paste on bare PCB’s, Programming to SMT machine regarding component locations on PCB, arrange components Reels & Trays respective to machine, Components Assembly, Maintain required Temperature.

Confidential

Project Lead

Responsibilities:

• As a Scrum Master Co-ordinated Daily stand-up meeting & Sprint Project Planning with others.
• Collection of Requirements and analysis.
• High Level Architectural approach.
• Preparation of Hardware requirement specification and High-level design document.
• Schematic Capture & Layout using ORCAD, Dx Designer, Zuken and Altium.
• Component Selection and BOM Preparation.
• Design Analysis I.e., Power Analysis and Placement analysis.
• Procurement of raw material.
• PCB layout support and verification.
• Board brings up, testing, Delivery to Customer.
• Debug the problems reported by costumer.